 |
Lap Joint flanges are used on piping fitted with lapped pipe or with lap joint stub ends. The lap joint flange with the stub end assembly are normally used in systems requiring frequent dismantling for inspection and cleaning and where the ability to swivel flanges and to align bolt holes materially eases the erection of large diameter or unusually stiff piping. These flanges are also used in applications where there is a need to facilitate bolt alignment.
These types of flanges are similar to slip-on flanges. The only difference is that it has a curved radius at the bore and face to accommodate a lap joint stub end. They may be used at all pressures and are available in a full size range. These lap joint flanges slip over the pipe, and are not welded. They are otherwise fastened to it. Here the bolting pressure is transferred to the gasket by the pressure of the flange against the back of the pipe lap. |
Lap Joint Flanges Key Features:
 Recommended in applications that require frequent dismantling of the flanges and pipe. - Used with a matching stub-end insert.
- Can rotate to allow for an easy alignment of bolt holes.
- Not recommended in extreme or high-pressure temperature applications.
Advantages of Lap Joint Flanges:
Lap Joint flanges have certain special advantages over other flanges. These are as follows:- Lap Joint flanges have the freedom to swivel around the pipe. This facilitates the lining up of opposing flange bolt holes.
- Lack of contact with the fluid inside the pipe leads to the greater durability of these flanges.
- In piping systems which corrode or erode quickly, the lap joint flanges may be salvaged for re-use.
- The pressure-holding capacity of lap joint flanges is little. But it is better than that of slip-on flanges.
- The Lap Joint works as a backing ring on the stub.
- The main advantage of lap joint flange is that the bolt holes can be aligned with the matching flange after
the welds have been completed.
- They allow rotational alignment capability.
Product range
Lap Joint Flanges Range
½” (15 NB) to 48” (1200NB) in 150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS ASA 150, ASA 300, PN 6,10,16,25, 40,64,100,160 ETC. Available with NACE MR 01-75
Stainless Steel Lap Joint Flanges
Grade : 304, 304L, 304H, 309, 310, 310S, 316, 316Ti, 316 L, 317, 317L, 321, 347, 347 H, 409, 410, 410S, 420, 430L
Duplex Steel Lap Joint Flanges
Grade : 2205 (UNS No. S31803), 2507 (UNS No. S32750)
Nickel Alloy Lap Joint Flanges
Grade : Nickel 200 (UNS No. N02200), Nickel 201 (UNS No. N02201), Monel 400 (UNS No. N04400), Monel 500 (UNS No. N05500), Inconel 800 (UNS No. N08800), Inconel 825 (UNS No. N08825), Inconel 600 (UNS No. N06600), Inconel 625 (UNS No. N06625), Inconel 601 (UNS No. N06601), Hastelloy C 276 (UNS No. N10276), Alloy 20 (UNS No. N08020), Titanium (Grade I & II)
Copper Alloy Lap Joint Flanges
Grade : UNS No. C 10100, 10200, 10300, 10800, 12000, 12200, 70600, 71500, UNS No. C 70600 (Cu -Ni- 90/10), C 71500 (Cu -Ni- 70/30)
Lap Joint Flanges Standard
ANSI : ANSI B16.5, ANSI B16.47, MSS SP44, ANSI B16.36, ANSI B16.48- DIN : DIN2527, DIN2566, DIN2573, DIN2576, DIN2641, DIN2642, DIN2655, DIN2656, DIN2627, DIN2628, DIN2629, DIN 2631, DIN2632, DIN2633, DIN2634, DIN2635, DIN2636, DIN2637, DIN2638, DIN2673
- B.S : BS4504 , BS4504, BS1560, BS10
- OTHER : PLATE, PLATE BLANK
Value Added Services for Lap Joint Flanges
HOT DIPPED GALVANIZING- HEAT TREATMENT
- CNC MACHINING
- THREADING
|
|
Steel Pipes & Tubes
Lap Joint Flanges